Pole placement and LQR implementation on longitudinal altitute holding control of wing in surface effect vehicle

Muhammad Nanda Setiawan, Evan Rizky Suryana, Leo Parytta, William Andaro

Abstract

The longitudinal altitude holding control system (LAHCS) of wing in surface effect (WiSE) vehicle has been developed using Simulink/Matlab. The LAHCS is designed to maintain the altitude of the vehicle stands at 1 m above the surface, with a maximum allowable deviation of 0.5 m. The purpose is to gain an additional lift generated by the surface effect to increase the aerodynamic performance. This control system is investigated using two approaches, i.e., the pole placement and the linear quadratic regulator (LQR) methods. Originally, the system shows an unstable response on the phugoid mode, indicated by the positive value of its Eigen. After the pole placement method is applied, the system is stable and capable of maintaining the reference command altitude. This method produces 0.27 of the maximum altitude deviation when the disturbance, represented by the doublet input elevator ±5° is applied. Moreover, the time needed for the system to reach the steady-state response of altitude is around 2.2 seconds. In comparison, the LQR method is also applied to the system with the same scenario. Although the settling time response is quite similar to the previous result, its maximum altitude deviation is significantly reduced by around 80 %. In conclusion, both of the methods used to design the LAHCS are capable of maintaining the altitude of the WiSE vehicle always below its maximum deviation tolerance.




Keywords


wing in surface effect vehicle; altitude holding control system; pole placement method; linear quadratic regulator (LQR); phugoid mode; doublet input elevator

Full Text:

PDF


References


R. Li and H. Chen, “The feasibility of high speed ground effect vehicles,” 17th AIAA Aviation Technology, Integration, and Operations Conference, 2017.

M. A. U. Amir and et al., “Wing in ground effect craft: a review of the state of current stability knowledge,” International Conference on Ocean Mechanical and Aerospace for Scientists and Engineer, 2016.

S. Wiriadidjaja, A. Zhahir, Z. H. Mohamad, S. Razali, A. A. Puaat and M. T. Ahmad, “Wing-in-Ground-Effect Craft: A Case Study in Aerodynamics,” International Journal of Engineering & Technology, vol. 7(4), pp. 5-9, 2018.

H. Wang, C. J. Teo, B. C. Khoo and C. J. Goh, “Computational Aerodynamics and Flight Stability of Wing-In-Ground (WIG) Craft,” Procedia Engineering, vol. 67, pp. 15-24, 2013.

M. M. Tofa, A. Maimun, Y. M. Ahmed, S. Jamei, A. Priyanto and Rahimuddin, “Experimental Investigation of a Wing-in-Ground Effect Craft,” The Scientific World Journal, vol. 2014, 2014.

N. Kornev, “On Unsteady Effects in WIG Craft Aerodynamics,” International Journal of Aerospace Engineering, vol. 2019, 2019.

Rahimuddin, A. Maimun, M. M. Tofa, S. Jamei and Tarmizi, “Stability Analysis of a Wing in Ground Effect Craft,” 14th International Ship Stability Workshop, Kuala Lumpur, 2014.

A. Nebylov and V. Nebylov, “Wing-in-Ground Effect Vehicles Flight Automatic Control Systems Development Problems,” Applied Mechanics and Materials, vol. 629, pp. 370-375, 2014.

H. Muhammad, Sembiring, Javensius, Jenie and D. Said, “Development of Automatic Flight Control Systems for Wing in Surface Effect Craft,” IFAC Proceedings, 2007.

W. Yang, Z. Yang and M. Collu, “Longitudinal Static Stability Requirements for Wing in Ground Effect Vehicle,” International Journal of Naval Architecture and Ocean Engineering, vol. 7(2), pp. 259-269, 2015.

L. Parytta and M. N. Setiawan, “Design of UAV Longitudinal Regulator System Stability Due to Turbulence on Cloud Seeding Operation: A Case Study of Wulung PA-07,” 7th International Seminar on Aerospace Science and Technology, Jakarta, 2019.

E. Rizky and M. N. Setiawan, “Design of UAV Lateral Regulator System Stability Due to Turbulence on Cloud Seeding Operation: A Case Study of Wulung PA-07,” 7th International Seminar on Aerospace Science and Technology, Jakarta, 2019.

R. Finck and D. E. Hoak, “The USAF Stability and Control DATCOM” Engineering Documents,” 1978.

Q. Qu, Z. Lu, P. Liu and R. K. Agarwal, “Numerical Study of Aerodynamicsof a Wing-in-Ground-Effect Craft,” Journal of Aircraft, vol. 51(3), pp. 913-924, 2014.

M. V. Cook, Flight Dynamics Principles “A Linear System Approach to Aircraft Stability and Control Third Edition,” Burlington, Ma: Elsevier, Ltd., 2012.

K. Ogata, “Modern Control Engineering,” New Jersey: Prentice Hall, 2010.

J. E. Cooper and J. R. Wright, “Introduction to Aircraft Aeroelasticity and Loads-Second Edition,” Chichester: John Wiley and Sons, 2015.

R. Szabolcsi, “Pole Placement Technique Applied in Unmanned Aerial Vehicles Automatic Flight Control Systems Design,” land Forces Academy Review, 23(1), pp. 88-98, 2018.

H. Purnawan, Mardlijah and E. B. Purwanto, “Design of Linear Quadratic Regulator (LQR) Control System for Flight Stability

of LSU-05,” 1st International Conference on Applied & Industrial Mathematics and Statistics, Pahang, 2017.

A. Jafar and et al, “A Robust ∞ H Control for Unmanned Aerial Vehicle Against Atmospheric Turbulence,” 2nd International Conference on Robotics and Artificial Intelligence, Rawalpindi, 2016.


Article Metrics

Metrics Loading ...

Metrics powered by PLOS ALM

Refbacks

  • There are currently no refbacks.




Copyright (c) 2020 Journal of Mechatronics, Electrical Power, and Vehicular Technology

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.